m0n0是基于freebsd而开发的软件路由器。由于freebsd有着比linux更高的稳定性、可靠性,所以用m0n0来做软件路由绝对是最好的选择。而且安装配置比coyote更简单,功能更强大,支持以下功能:

1、Web interface (supports SSL)
2、serial console interface for recovery
3、set LAN IP address
4、reset password
5、Restore factory defaults
6、reboot system
7、wireless support (access point with PRISM-II/2.5 cards, BSS/IBSS
with other 8、cards including Cisco)
9、captive portal (in the latest beta version)
10、stateful packet filtering
11、block/pass rules
12、logging
13、NAT/PAT (including 1:1)
14、DHCP client, PPPoE, PPTP and Telstra BigPond support on the WAN
interface
15、IPsec VPN tunnels (IKE; with support for hardware crypto cards
and mobile clients)
16、PPTP VPN (with RADIUS server support)
17、static routes
18、DHCP server
19、caching DNS forwarder
20、DYnDNS client
21、SNMP agent
22、traffic shaper
23、firmware upgrade through the web browser
24、Wake on LAN client (in the latest beta version)
25、configuration backup/restore
26、host/network aliases

目前在m0n0的网站上提供有稳定版本了开发版本两种类型,如果追求新功能,就用新版本,如果要稳定,就用老版本喽!

新版本基于freebsd4.10,修正以前的很多bug.

在下载页面中,又提供了好几种类型:cf卡启动、从标准的电脑硬盘启动、从光盘启动用软盘来保存配置文件等等。并提供了下载文件。

地址为:
http://www.m0n0.ch/wall/downloads.php

我要谈的就是从硬盘运行的方法。
安装到硬盘上的步骤为:
Installation on a standard PC (CF/IDE version)
Installation on a standard PC requires the following steps:
一、download the raw CF/IDE image (generic-pc)
write the image to a CF card (> 5 MB) or an IDE hard disk,
either with dd under FreeBSD or under Windows with my tool,
physdiskwrite 0.4 (下载m0n0的硬盘启动映象文件,地址为:
http://high5.net/mirrors/m0n0.ch/generic-pc-1.0.img

(稳定版本)
http://m0n0wall.jetpress.net/generic-pc-1.1b14.img

(开发版本)
同时下载映象文件写入工具physdiskwrite,地址为:
http://www.m0n0.ch/wall/downloads/physdiskwrite-0.4.zip

二、Windows:
(use the -u flag if the target disk is > 800 MB – make very sure
you’ve selected the right disk!!)
physdiskwrite [-u] generic-pc-xxx.img
(you must use v0.3 or later!)
(将要做路由器的硬盘接到现有的windows系统电脑中,将映象文件写入硬盘)

三、put the CF card/HD into the target PC
(把硬盘安装到目标机器中)
四、plug the PC into the network (LAN/WAN/…)
(接好网络设备)
五、power it up
六、assign functions (LAN/WAN/OPT) to your interfaces (hint: use
auto-detection, or let the MAC addresses tell you which card is
which one)
change the LAN IP address, or use the default (192.168.1.1;
m0n0wall acts as a DHCP server by default)
access the webGUI (user: ‘admin’, default password: ‘mono’)
make the necessary changes to the default configuration

简而言之,就是将下载到的映象文件写到一个800M以上的硬盘上以后,就可以通过http://192.168.1.1进行各项功能设定、管理了。

说明文档:
http://www.m0n0.ch/wall/docbook/

发表评论

电子邮件地址不会被公开。 必填项已用*标注